Kloubová oka Fluro

30 FLURO ® -Gelenklager GmbH 3 1) 6 4,50 14 21 27 6,5 5,0 5,1 5,5 M 3 10 8,0 1,8 14 6 5 8 6,00 18 27 36 11,0 9,0 7,7 9,0 M 5 10 11,8 3,3 1200 13 18 6 9 6,75 20 30 40 13,0 10,0 8,9 11,0 M 6 12 13,1 4,3 1500 13 27 8 12 9,00 24 36 48 16,0 12,5 10,4 13,0 M 8 16 20,7 7,1 1200 14 46 10 14 10,50 28 43 57 19,0 15,0 12,9 17,0 M 10 20 28,3 10,0 1000 13 76 12 16 12,00 32 50 66 22,0 17,5 15,4 19,0 M 12 22 34,5 13,5 860 13 115 14 19 13,50 36 57 75 25,0 20,0 16,8 22,0 M 14 25 39,5 17,0 750 16 170 16 21 15,00 42 64 85 27,0 22,0 19,3 22,0 M 16 28 60,5 21,5 660 15 230 18 23 16,50 46 71 94 31,0 25,0 21,8 27,0 M 18x1,5 32 73,0 26,0 600 15 320 20 25 18,00 50 77 102 34,0 27,5 24,3 32,0 M 20x1,5 33 83,0 31,5 540 14 415 22 28 20,00 54 84 111 37,0 30,0 25,8 32,0 M 22x1,5 37 100,0 38,0 500 15 540 25 31 22,00 60 94 124 42,0 33,5 29,6 36,0 M 24x2 42 118,0 47,1 440 15 750 30 37 25 ,00 70 110 145 51 ,0 40,0 34,8 41,0 M 30x2 51 155,0 64,0 370 17 1130 35 43 28,00 80 125 165 58,0 46,0 37,7 50,0 M 36x2 56 191,0 80,0 330 19 1600 40 49 35 ,00 90 142 187 69 ,0 57,0 44,2 60,0 M 42x2 60 235,0 116,0 290 16 2770 B M A F l K J Gl SW o G Rod Ends Series K - stainless housing - requiring maintenance Series GiRS Rod End with female thread regreasable through grease nipple in the housing For use in corrosive environments Materials: Housing: Stainless steel to 1.4057, Aisi 431, forged, polished size 40 turned from stainless steel to 1.4057, Aisi 431 insert: Special high strength bronze to CuSn8 Ball: Bearing steel to 100Cr6, Aisi 52100, hardened, ground, polished, hard chrome plated on the running surface on request: other slide pairings possible This series is also available sealed (see page 52) or with threaded bolt (see page 53). Cetop connections see page 54. 1) without lubrication hole Size (D H7) Static load C o kN Dynamic load C kN limiting speed rev/min Weight g Maximum Pivoting Angle (°) only for short-term revolutions recommended