Kloubová oka Fluro

38 FLURO ® -Gelenklager GmbH 4 1) 7 5,25 14 24 31 9,5 7,8 6,5 8 M 4 12 2,5 5,1 14 11 5 8 6,00 18 27 36 11,0 9,0 7,7 9 M 5 10 11,8 7,5 600 13 18 6 9 6,75 20 30 40 13,0 10,0 8,9 11 M 6 12 13,1 9,3 530 13 27 8 12 9,00 24 36 48 16,0 12,5 10,4 13 M 8 16 20,7 16,7 420 14 46 10 14 10,50 28 43 57 19,0 15,0 12,9 17 M 10 20 28,3 23,4 350 13 76 12 16 12,00 32 50 66 22,0 17,5 15,4 19 M 12 22 34,5 32,0 300 13 115 14 19 13,50 36 57 75 25,0 20,0 16,8 22 M 14 25 39,5 42,0 260 16 170 16 21 15,00 42 64 85 27,0 22,0 19,3 22 M 16 28 60,5 52,5 230 15 230 18 23 16,50 46 71 94 31,0 25,0 21,8 27 M 18x1,5 32 73,0 64,0 210 15 320 20 25 18,00 50 77 102 34,0 27,5 24,3 32 M 20x1,5 33 83,0 78,0 190 14 415 22 28 20,00 54 84 111 37,0 30,0 25,8 32 M 22x1,5 37 100,0 97,0 170 15 540 25 31 22,00 60 94 124 42,0 33,5 29,6 36 M 24x2 42 118,0 122,0 150 15 750 30 37 25 ,00 70 110 145 50 ,0 40,0 34,8 41 M 30x2 51 155,0 168,0 130 17 1130 35 43 28,00 80 125 165 58,0 46,0 37,7 50 M 36x2 56 191,0 206,0 110 19 1600 40 49 35 ,00 90 142 187 69 ,0 57,0 44,2 60 M 42x2 60 235,0 286,0 100 16 2770 B M A F l K J Gl SW o G ! Rod Ends Series K - Stainless, Maintenance Free Series GiRSW Rod End with female thread and PTFE liner For use at high dynamic pressure and tension loads in corrosive environments Size (D H7) Static load C o kN Dynamic load C kN limiting speed rev/min Weight g Materials: Housing: Stainless steel to 1.4057, Aisi 431, forged, polished size 40 turned from stainless steel to 1.4057, Aisi 431 insert: Special high strength bronze to CuSn8 with PTFE liner bonded to the inner surface Ball: Bearing steel to 100Cr6, Aisi 52100, hardened, ground, polished, hard chrome plated on the running surface This series is also available sealed (see page 52) or with threaded bolt (see page 53). Cetop connections see page 54. 1) Size 4 on request. Housing turned from stainless steel to 1.4305, Aisi 303 / 1.4301, Aisi 304 only for short-term revolutions recommended Please note: The dynamic load "C" of the bearing of some rod ends is in some sizes higher than the static load "C o " of the rod end. Maximum Pivoting Angle (°)