Kloubová oka Fluro

46 FLURO ® -Gelenklager GmbH 4 1) 7 5,25 14 24 31 9,5 7,8 6,5 8 M 4 12 1,7 5,1 14 11 5 8 6,00 18 27 36 11,0 9,0 7,7 9 M 5 10 7,0 7,5 600 13 18 6 9 6,75 20 30 40 13,0 10,0 8,9 11 M 6 12 7,5 9,3 530 13 27 8 12 9,00 24 36 48 16,0 12,5 10,4 13 M 8 16 12,5 16,7 420 14 46 10 14 10,50 28 43 57 19,0 15,0 12,9 17 M 10 20 17,5 23,4 350 13 76 12 16 12,00 32 50 66 22,0 17,5 15,4 19 M 12 22 20,5 32,0 300 13 115 14 19 13,50 36 57 75 25,0 20,0 16,8 22 M 14 25 24,0 42,0 260 16 170 16 21 15,00 42 64 85 27,0 22,0 19,3 22 M 16 28 37,0 52,5 230 15 230 18 23 16,50 46 71 94 31,0 25,0 21,8 27 M 18x1,5 32 45,5 64,0 210 15 320 20 25 18,00 50 77 102 34,0 27,5 24,3 32 M 20x1,5 33 51,5 78,0 190 14 415 22 28 20,00 54 84 111 37,0 30,0 25,8 32 M 22x1,5 37 62,0 97,0 170 15 540 25 31 22,00 60 94 124 42,0 33,5 29,6 36 M 24x2 42 73,5 122,0 150 15 750 30 37 25 ,00 70 110 145 50 ,0 40,0 34,8 41 M 30x2 51 97,0 168,0 130 17 1130 35 43 28,00 80 125 165 58,0 46,0 37,7 50 M 36x2 56 121,0 206,0 110 19 1600 40 49 35 ,00 90 142 187 69 ,0 57,0 44,2 60 M 42x2 60 145,0 286,0 100 16 2770 B M A F l K J Gl SW o G ! Rod Ends Series K - Stainless, Maintenance Free Series GiRSW..NiRo Rod End with female thread and PTFE liner bonded to the inner surface, completely in AISI 316 For use at high dynamic pressure and tension loads in corrosive environments Size (D H7) Materials: Housing: Stainless steel to 1.4404, Aisi 316 insert: Stainless steel 1.4571 with PTFE liner bonded to the inner surface Ball: Stainless steel 1.4404, Aisi316, ground, polished This series is also available sealed (see page 52) or with threaded bolt (see page 53). Cetop connections see page 54. 1) on request Please note: The dynamic load "C" of the bearing of some rod ends is in some sizes higher than the static load "C o " of the rod end. Static load C o kN Dynamic load C kN limiting speed rev/min Maximum Pivoting Angle (°) only for short-term revolutions recommended Weight g